24car-repair.com
1 Lincoln MKC Oil Capacity Calculator
Accurate oil capacity calculation for all Lincoln MKC models (2015-2019)
This advanced calculator provides precise engine oil capacity data for Lincoln MKC vehicles based on official manufacturer specifications. Proper oil capacity is critical for maintaining engine health, performance, and longevity.
2 Calculation Results
Your Lincoln MKC requires:
for a complete oil change with filter replacement
Always verify the oil level using your vehicle’s dipstick after adding oil. The calculated capacity provides a starting point, but actual requirements may vary slightly based on oil drainage completeness and measurement accuracy.
3 Comprehensive Guide to Lincoln MKC Engine Oil Capacity
3.1 Understanding Engine Oil Capacity Specifications
Engine oil capacity refers to the total volume of oil required to properly lubricate your Lincoln MKC’s engine after a complete drain. This specification varies based on multiple factors including engine displacement, model year, and whether you’re replacing the oil filter.
The Lincoln MKC, produced from 2015 to 2019, features two engine options: the standard 2.0L EcoBoost I4 and the performance-oriented 2.3L EcoBoost I4. Both engines utilize turbocharged direct injection technology that requires specific oil formulations and precise quantities for optimal performance.
Incorrect oil capacity can lead to serious engine damage. Overfilling can cause oil foaming and inadequate lubrication, while underfilling can result in insufficient oil pressure and increased engine wear. Always use the dipstick to verify the final oil level after any change.
3.2 Complete Oil Capacity Reference Table
The following table provides comprehensive oil capacity data for all Lincoln MKC models and configurations:
| Model Year | Engine Type | Oil Capacity (With Filter) | Oil Capacity (Without Filter) | Recommended Oil Type | Drain Plug Torque |
|---|---|---|---|---|---|
| 2015 | 2.0L EcoBoost I4 | 5.7 quarts (5.4L) | 5.2 quarts (4.9L) | SAE 5W-30 Synthetic | 18 lb-ft (24 Nm) |
| 2015 | 2.3L EcoBoost I4 | 6.0 quarts (5.7L) | 5.5 quarts (5.2L) | SAE 5W-30 Synthetic | 18 lb-ft (24 Nm) |
| 2016 | 2.0L EcoBoost I4 | 5.7 quarts (5.4L) | 5.2 quarts (4.9L) | SAE 5W-30 Synthetic | 18 lb-ft (24 Nm) |
| 2016 | 2.3L EcoBoost I4 | 6.0 quarts (5.7L) | 5.5 quarts (5.2L) | SAE 5W-30 Synthetic | 18 lb-ft (24 Nm) |
| 2017 | 2.0L EcoBoost I4 | 5.7 quarts (5.4L) | 5.2 quarts (4.9L) | SAE 5W-30 Synthetic | 20 lb-ft (27 Nm) |
| 2017 | 2.3L EcoBoost I4 | 6.0 quarts (5.7L) | 5.5 quarts (5.2L) | SAE 5W-30 Synthetic | 20 lb-ft (27 Nm) |
| 2018 | 2.0L EcoBoost I4 | 5.7 quarts (5.4L) | 5.2 quarts (4.9L) | SAE 5W-30 Synthetic | 20 lb-ft (27 Nm) |
| 2018 | 2.3L EcoBoost I4 | 6.0 quarts (5.7L) | 5.5 quarts (5.2L) | SAE 5W-30 Synthetic | 20 lb-ft (27 Nm) |
| 2019 | 2.0L EcoBoost I4 | 5.7 quarts (5.4L) | 5.2 quarts (4.9L) | SAE 5W-30 Synthetic | 20 lb-ft (27 Nm) |
| 2019 | 2.3L EcoBoost I4 | 6.0 quarts (5.7L) | 5.5 quarts (5.2L) | SAE 5W-30 Synthetic | 20 lb-ft (27 Nm) |
3.3 Technical Specifications and Requirements
The Lincoln MKC’s EcoBoost engines employ advanced forced induction technology that imposes specific requirements on engine oil:
3.3.1 Oil Viscosity Requirements
All Lincoln MKC models require SAE 5W-30 synthetic motor oil that meets Ford specification WSS-M2C946-B1. This specific formulation provides:
- Optimal flow characteristics during cold starts (5W rating)
- Sufficient film strength at high temperatures (30 rating)
- Enhanced protection for turbocharger bearings
- Improved resistance to thermal breakdown
3.3.2 Oil Filter Specifications
The factory-recommended oil filter for Lincoln MKC models is the Motorcraft FL-910S. This filter features:
- High-efficiency synthetic media (traps particles as small as 20 microns)
- Anti-drainback valve to prevent dry starts
- Rugged steel base plate and housing
- Maximum operating pressure: 225 psi
3.3.3 Drain and Refill Procedure
For a complete oil change, follow this procedure:
- Run the engine for 5-10 minutes to warm the oil (improves drainage)
- Securely lift the vehicle using proper jacking points
- Place drain pan beneath oil drain plug
- Remove drain plug using a 13mm socket (allow oil to drain completely)
- Remove old oil filter using appropriate filter wrench
- Install new filter with a light coating of oil on the gasket
- Reinstall drain plug with new washer, torquing to specification
- Add calculated amount of oil through fill port
- Start engine, check for leaks, then verify oil level with dipstick
